• CP-WO-009,MY SHOP,CP-WO-009
  • CP-WO-009,MY SHOP,CP-WO-009

CP-WO-009 Wood-Look Inorganic Fibre Wall Board

A wood-look decorative board on an inorganic fibre core: warm timber appearance for interior walls, ceilings and exterior facade panels.
  • CP-WO-009,MY SHOP,CP-WO-009

Description

Product Overview

CP-WO-009 is a wood-look decorative board built on an inorganic fibre core. Its face carries a light, warm wood grain with fine vertical lines and a smooth, matte finish; underneath that surface there is no timber veneer and no resin-rich composite, only a fully vitreous inorganic board made by remelting and restructuring coal gasification slag — an industrial by-product — in two stages at 1,500 °C. Because the wood appearance is a finished decorative surface rather than a species of timber, it stays usable where solid timber becomes a maintenance problem: interior feature and corridor walls, ceilings and soffits, bathroom, kitchen and balcony wall linings, and exterior facade zones that want the warmth of timber without a protection and re-finishing cycle.

Design teams sometimes draw an elevation in metal exterior wall panels and ask for a warmer surface part-way through the scheme. The wood-look references sit in the same product family, use the same panel formats and follow the same setting-out logic, so changing the surface does not mean redesigning the wall.

This board is one reference in the wood-look band, which runs from CP-WO-001 to CP-WO-017. The companion references in the same series — CP-WO-001, CP-WO-002, CP-WO-003, CP-WO-004, CP-WO-005, CP-WO-006, CP-WO-007, CP-WO-008, CP-WO-010, CP-WO-011, CP-WO-012, CP-WO-013, CP-WO-014, CP-WO-015, CP-WO-016 and CP-WO-017 — carry the other wood tones and grain directions. Choosing the tone and the grain direction together, and keeping a single wall inside one band, is what makes the joints read as one field.

We are one of the exterior metal wall panels manufacturers who produce both the core and the decorative surface in-house, so the wood-look, metal-look and stone-look references come off the same production line and the same quality checks instead of being bought in from different sources.

That matters on a mixed envelope. Where part of the elevation is carried in exterior metal facade panels and another part in wood-look boards, both are quoted, produced and delivered as one package, which keeps the setting-out and the delivery schedule consistent across the facade.

Board Specifications

Property Value
Base material Inorganic fibre board made from coal gasification slag
Surface Decorative wood-grain finish, matte
Panel length Up to 3,050 mm
Panel width Up to 1,220 mm
Thickness range across the series 4 mm to 15 mm
Exterior wall thicknesses 10 mm and 12 mm
Interior wall thicknesses 4 mm, 6 mm, 8 mm and 10 mm
Density, series range Approximately 950 to 1,200 kg/m³, or higher depending on the series

Wood Grain & Surface

  • Tone and grain. The face reads as a light, warm timber — fine vertical grain lines over a pale golden-brown base, closer to a limed timber than to a dark hardwood. It is a decorative surface, not a timber face.
  • Matte, low sheen. The finish is smooth and non-reflective, so large wall fields and ceilings stay even under raking daylight or downlights instead of flashing back at the viewer.
  • One grain direction. The lines run one way along the panel, which is what gives the surface its timber character. A board turned through 90 degrees against its neighbours reads differently, even though the tone is the same.
  • Smooth to the touch. The grain is a fine printed line rather than a deep relief, so there are no raised ridges catching the light along a joint and the face is easy to wipe over.
  • Approve a physical sample. Ask to see a board before the order is released. A screen cannot show how a warm wood tone sits against the brick, render or metal it will stand next to.
  • Keep one wall in one run. Where a wall has to read as a continuous field, bring the whole elevation into a single production run and a single batch reference. Boards from a later run can be ordered for other walls, but they should not be mixed into the same field.
  • Send a tone reference. A photograph or a physical sample of the timber you have in mind is enough for our team to identify the closest references in the wood-look band, and it is the quickest way to settle the appearance question.

Applications & Wall Zones

In offices, showrooms and hotel lobbies the board is the warm element in an otherwise hard interior — a reception wall behind a desk, a lift lobby, a boardroom wall, a store back wall. It goes flat onto a prepared substrate, so the wall reads as one continuous timber surface without a heavy batten build-up.

Corridor and waiting walls in public and institutional buildings are a second use. These are surfaces in daily contact with trolleys, bags and cleaning equipment, and the design usually wants something warmer than a plain board without turning the wall into something that has to be redecorated.

Soffits and ceilings are one of the strongest uses for a wood-look face: entrance canopies, colonnades, balcony soffits and covered walkways, where the panel is seen from below and the grain runs along the length of the space.

Wet walls are a harder test for any timber look. Bathroom, kitchen and balcony walls take this surface because the appearance sits on an inorganic core rather than on wood, and joints and edges are sealed as part of the lining.

On an exterior wall, wood-look is normally an accent rather than the whole envelope: an entrance portal, a recessed bay, an upper-storey band or infill between openings. Where the main elevation is drawn in exterior metal wall panels, the wood-look zones are simply another surface on the same family of boards.

Mixed-finish elevations work because every series shares the panel formats. Wood-look panels banded with stone-look boards and metal exterior wall panels can be set out once, on one drawing, and ordered by zone.

On larger projects the wood-look zones are usually one part of a wider surfacing package. The metal-look and stone-look boards and the aluminium mosaic line all come from the same company, which answers the procurement question directly: an exterior wall panels supplier that holds the whole range does not leave a project splitting its finishes across several orders.

Fixing & Installation Notes

  1. Confirm the build-up and the fixing method before the order is placed. Wet bonding, riveting and dry hanging are all used with this board, and each route assumes a different substrate, a different joint detail and a different sequence on site, so the method belongs on the drawing rather than in a decision taken on the scaffold.
  2. Set the grain direction and the joint layout out together. The grain runs one way along the panel, so the drawing has to fix the run before anything is cut, and the joint module has to follow it.
  3. Prepare the substrate. Wet bonding needs a sound, flat, clean background; riveted and dry-hung work is carried by a sub-frame whose setting-out follows the panel module. Check the background before the first panel goes on, not after.
  4. Cut and drill on site with normal tools. The board can be cut, drilled, nailed and screwed, and the supplied figure for screw withdrawal is at least 1,870 N — ask your sales contact to confirm the value that applies to the thickness you order. Support the panel while you work and cut from the face side so the decorated edge is not lifted.
  5. Fix, then check the joints. Keep the joint width and the shadow line consistent across the wall, including at corners and returns, because an irregular joint is the first thing the eye finds on a wood grain field.
  6. Seal, flash and drain. On an exterior wall, joints are sealed and the head, sill, edges and openings are flashed as part of the wall system, and drainage paths have to stay clear. The panel is one component of that construction, not the whole weather line.
  7. Protect the work and hand it over clean. Stack boards flat and dry, lift rather than drag them into position, and keep the surfaces clean while the other trades finish. Pass the fixing schedule, the batch references and the installation instructions into the maintenance file, and compare the finished wall with the approved sample before sign-off.

Fire, Moisture & Air Quality

Fire performance is recorded in two separate statements, and it is worth keeping them apart when a submission is being prepared. The supplied test information classifies the board itself as Class A non-combustible. Separately, the tested wall-panel system is reported at 90 minutes of fire resistance at 1,200 °C, and that result belongs to one particular construction of panel, substructure, joints and fixings rather than to a sheet on its own; smoke toxicity is reported as Class t0. Anyone weighing exterior metal wall panels against this board for a fire-reviewed wall is choosing between two wall systems, not between two surface finishes.

The supplied information describes the board as formaldehyde-free and benzene-free, with no toxic volatile organic compounds detected, which matters wherever the finished surface sits inside an occupied space rather than on an outer skin.

Moisture behaviour is what allows a wood look where timber could not be used. Moisture expansion is reported at 0.1 % or less, and mould resistance is covered in the same test set. That is the basis for putting the board into bathrooms, kitchens and balcony walls, and onto exterior elevations where the design wanted timber but the specification was drawn around exterior metal facade panels.

On an exterior wall the figures to read belong to the whole assembly. The reported system values are Class 5 air tightness, Class 3 water tightness and wind resistance of plus or minus 6.0 kPa. Change the substructure, the joint width or the fixing, and the tested result no longer describes what is standing on the building — the same rule that applies to metal exterior wall panels or to any other clad system. Verify the construction against the project report and the local code before the wall is signed off.

Care & Maintenance

  1. Clean with water and a mild detergent. A soft cloth or sponge and a neutral cleaner handle day-to-day marks; the decorative surface is stain, scratch and wear resistant, so there is no polishing or recoating step in the routine.
  2. Deal with spills and strong stains promptly. Wipe them off rather than letting them sit overnight, which is the difference between a wipe and a scrub on any decorative surface.
  3. Keep abrasives and strong solvents away from the face. Wire wool, scouring pads and aggressive solvents can dull the matte finish or leave a sheen difference against the panels around them.
  4. Check the exterior system, not just the panel. On an exterior wall, look at the sealant lines, the flashings and the drainage outlets during the routine facade inspection; a blocked outlet does more harm than anything that happens to the surface itself.
  5. Look at fixings and trims at the same time. Loose trims, rivets and fixings are quick to deal with during a scheduled inspection and expensive to repair after a storm.
  6. Keep a couple of boards from the original run. If a panel is later damaged, a replacement ordered against the same series will match the wall far better if you still have a board from that production run to compare against.
  7. Do not use the finished surface as a work platform. Damage usually arrives with the other trades rather than with the weather — a ladder, a stacked crate or a cutting board resting against a newly clad wall is the usual source.

Ordering & Delivery

  • What to send with an enquiry. The wall position and whether it is interior or exterior, the panel size and thickness, the surface finish, the quantity, the project location and the required delivery date. With those in the enquiry we can return a priced offer and the technical information that belongs to the order.
  • Panel schedule. Send the elevation drawing with the thicknesses marked against each wall, so the offer follows the design rather than an assumed panel.
  • Lead time. Custom orders: 30 days. Confirm the programme with your sales contact as soon as the panel schedule is fixed.
  • Minimum quantity, packing and shipping. These are agreed against the panel format, the finish and the destination, so they are confirmed with your sales contact rather than published as a fixed rule.
  • Samples. Ask your sales contact about sample availability and how long a sample takes to reach you; a physical board is the only reliable way to judge a wood tone against the rest of the scheme.
  • Documents. Tell your contact which records the client, consultant or authority needs to see. Our published test list covers fire resistance, mould resistance, antiviral activity, radioactivity, VOC and scrapped-off toy material, and the package that fits a particular market is agreed at order stage.
  • Comparing quotes. If you are collecting prices from several exterior metal wall panels manufacturers, ask each one to quote against the same panel schedule, thicknesses and finishes; it is the only way the numbers line up.
  • Quoted direct. As an exterior wall panels supplier we quote from our own production base rather than through a trading layer, so the figures you receive come from the people who will make the panels.
  • Phased projects. If the cladding is going to be released in stages, say so at the first order and list the walls that follow, so the later phases can be planned against the same schedule.

Scale & Supply Capability

CERSAIPANEL is the brand of Yulin Keli Keying Technology Co., Ltd., a building-material manufacturer established in 2016 and based in Yulin, Shaanxi, where we run our own production base with a workforce of 140. Manufacturing and export sit under one roof, so buyers in Europe, North and South America and Australia deal directly with the people who make the goods. Our full range is backed by third-party testing and the international certifications the company holds, and we take on OEM work and custom orders, from first sample through repeat production.

FAQ

Can this board be used on an exterior wall?

Yes. The board is offered for exterior facades as well as interior walls. Outside, it is carried on a drained and ventilated build-up like our exterior metal facade panels, while interior walls are fixed flat to a prepared substrate, so the two conditions are detailed differently even though the panel arrives the same. Because exterior performance is proven as a complete wall assembly, the substructure, joint width and fixing method have to follow the project's own design.

Can wood-look panels be combined with metal or stone surfaces on one elevation?

Yes. The wood-look, stone-look and metal-look references come from the same range and the same production line, so panel formats, setting-out and joint widths carry across a banded wall. We are among the exterior metal wall panels manufacturers who print and cure the decorative surface in-house, which is why a mixed-finish package can be quoted, produced and delivered as one order.

Is the board suitable for bathrooms, kitchens and other wet walls?

It is used on bathroom, kitchen and balcony walls, where a wood appearance normally would not be specified because the face is not timber. Joints, edges and penetrations still have to be sealed as part of the lining, exactly as they would be for any other wet-area panel. Ask your sales contact for the moisture and mould test data that applies to the thickness you plan to order.

What is the difference between this wood-look board and a metal exterior wall panel?

The board underneath is from the same inorganic fibre family; the difference is the decorative surface. A wood-look board and a metal exterior wall panel are chosen for the appearance an elevation needs, and both take the same panel formats, the same fabrication and the same fixing routes. Material performance does not change with the surface, so the choice is normally made on look and on the wall position.

Does the surface need sealing, oiling or refinishing after installation?

No. The wood grain is part of the finished decorative face rather than a raw timber surface, so there is no sanding, staining or re-oiling cycle attached to it, and routine care is cleaning. The supplied information describes the surface as stain, scratch and wear resistant.

How does the board compare in weight with stone or ceramic finishes?

It is offered as a lighter alternative to stone, ceramic tile and several traditional panel systems. What matters for a structural check is the weight of the finished wall at the thickness and build-up you select, so ask your sales contact for the figure for your panel before the load calculation is closed.

Which other surfaces are available if the project needs more than wood-look?

The same board platform carries metal-look and stone-look references, and the range also includes decorative aluminium mosaic for interior walls. They can be quoted as one package, so a project that wants a single exterior wall panels supplier for every decorative surface does not have to split the order.

Leave a message
姓名
电子邮件*
信息