• CP-MT-002,MY SHOP,CP-MT-002
  • CP-MT-002,MY SHOP,CP-MT-002

CP-MT-002 Metal-Look Exterior Wall Panel

Metal-look exterior fibre wall board with a matte metal-texture face, made from coal gasification slag. Available in exterior and interior grades.
  • CP-MT-002,MY SHOP,CP-MT-002

Description

Product Overview

CP-MT-002 is an inorganic fibre decorative board with a factory-applied metal-look face, part of our metal-texture series. The panel itself is a rigid, glass-phase inorganic board; the metal appearance comes from a decorative surface applied at the factory, so the board arrives finished and there is nothing to clad or paint over on site.

The board is chosen where a wall needs the character of metal — a matte, finely speckled face that reads as metal from across a road and shows its grain close up — without the handling, cutting and fixing that sheet-metal cassettes demand. It goes onto exterior walls as a cladding panel over a sub-frame, and indoors onto walls, ceilings, partitions and joinery, where one factory-finished surface can carry a large area without visible variation.

Buyers who specify it are usually running a facade or an interior package and want a material that brings its own finish and can be worked with ordinary tools. As an exterior wall panels supplier we quote from your elevations and panel layout rather than from a stock list, so the grade, the panel size and the surface all follow the job in front of you.

The heavier exterior grades and the lighter interior grades come from the same production base, and the board takes all three common fixing methods — wet bonding, riveting and dry hanging — which means the same material can be detailed for a curtain wall and for a corridor wall in the same project.

Material & Build

  • Base material — the board is built from coal gasification slag, the solid by-product left behind when coal is gasified, instead of from quarried mineral.
  • Two-stage melting — the raw material passes through two melts at 1,500 °C; harmful substances are burned out and what remains is a clean, restructured chemical composition.
  • Glass-phase structure — the finished panel is fully vitreous and inorganic, with no resin binder holding it together, and it is not a carbon-fibre-reinforced polymer composite.
  • Emission profile — no formaldehyde and no benzene are detected in the supplied test information, and no toxic volatile organic compounds were detected either, which matters when the board goes onto the inside face of a building.
  • Feedstock choice — using an industrial by-product rather than basalt or another quarried mineral means the board is made without depleting natural mineral resources.
  • Process energy — the melting stage runs on green electricity generated from wind and solar, which reduces the energy consumption and carbon emissions of the process.
  • Board build — the panel arrives flat and rigid with the decorative face already applied, so metal exterior wall panels from this series are supplied finished rather than as raw substrate waiting for a coating.
  • Workability — the same build lets the board be cut, drilled, nailed and screwed with standard tools, so a fabricator does not need a separate processing line to handle it.

Metal Surface & Finish

The face on this board is a matte metal texture with a fine speckle and a warm tan-through-brown tonal movement. It is closer to a patinated or weathered metal than to a bright brushed sheet or a mirror-polished surface, and the unevenness is deliberate: on a large field the tone shifts gently across the elevation instead of flattening into a single flat colour.

Because the finish is matte, it throws very little glare. On an elevation that catches sun for part of the day that keeps the wall comfortable to look at, and it also means small handling marks picked up on site are far less visible than they would be on a glossy surface. At street level the panel reads as metal; at arm's length the grain and speckle are clearly visible, which is usually what a design team is looking for when they choose a metal look over a painted board.

The face is applied in the factory, which is why metal exterior wall panels from this series arrive with nothing left to paint or laminate on site. Where a panel is trimmed, the cut edge shows the board core, so edge details, trims and corner returns are worth settling on the drawing rather than on the scaffold.

Colour and pattern are agreed against a physical reference before production. Confirm the colour reference that applies to your project at the quotation stage, and check the approved sample in daylight against the elevation it is going on, because the same finish reads differently against a dark reveal and against an open wall.

Specifications

Property Detail
Base material Inorganic fibre decorative board
Surface Decorative metal-look face
Apparent density approx. 950–1,200 kg/m³, higher depending on the series
Panel thickness, exterior walls 10 mm and 12 mm
Panel thickness, interior walls 4 mm, 6 mm, 8 mm and 10 mm
Thickness range across the series 4–15 mm, depending on the series
Panel length up to 3,050 mm
Panel width up to 1,220 mm

Fire, Moisture & Strength

The supplied test information classifies this board as Class A non-combustible. That classification describes the material itself and is worth keeping separate from the second result, which belongs to the wall: the tested wall-panel system reports 90 minutes of fire resistance at 1,200 °C, and smoke toxicity is reported as Class t0 with no toxic volatile organic compounds detected. Fire ratings depend on the panel specification, the substructure, the joints and the installation system, so the figures that go into a submission should be verified against the project report and the local building code rather than taken from this product alone.

Moisture behaviour is the other half of the exterior question. The board's moisture expansion is 0.1% or less in the supplied test information, which is why it is offered for both exterior walls and wet interior areas such as bathrooms, kitchens and balconies. On the outside, the tested system values include Class 5 air tightness, Class 3 water tightness and wind resistance of plus or minus 6.0 kPa. Those results belong to a correctly built wall, so sealing, flashing and drainage details still have to be designed and installed properly — the board does not replace them.

Mould resistance is covered in the same test documentation, which is the reason the board is used in humid interiors where a paper-faced or gypsum-based board would be at risk.

Screw withdrawal strength is at least 1,870 N, so mechanical fixings hold firmly even after panels have been handled and re-fixed during a long facade programme. Together with the density range, that figure is what we as exterior metal wall panels manufacturers supply to a structural or fixing designer working out centres and edge distances.

On exterior metal facade panels, these numbers describe the tested construction rather than the bare board, so pass the wall build-up to us with your enquiry and we will confirm which values apply to your detail.

Installation Methods

  1. Confirm the wall build-up first — substrate type, insulation, cavity and drainage, exposure, and whether the wall is an exterior facade or an interior partition. This decision drives everything that follows.
  2. Choose the fixing method. Wet bonding suits flat, sound substrates; riveting fixes the panel mechanically to a frame; dry hanging on a carrier system is usual for larger areas and wherever individual panels may need to be removed later.
  3. Set out the panel grid from the approved layout, so joint lines run consistently across the elevation and any cut panels land where they are least conspicuous.
  4. Cut, drill, nail and screw with standard tools. Keep the decorative face protected while working, and take trimming cuts so the finished edge lands where the detail expects it.
  5. Fix to the approved centres and leave the designed movement at the joints. Do not assume the board can span further than the fixing design allows, and do not bond onto a damp or dusty substrate.
  6. Seal the joints, flashings and drainage paths on exterior work. Seal a cavity that is meant to drain and you trap water behind the cladding, which is the most common way a good panel system fails.
  7. Clean down as the work proceeds, and leave the final clean until the surrounding trades have finished. Installation should be carried out by an experienced contractor working to the current technical instructions for the project.

Applications

  • Commercial facades and curtain walls — office, commercial and mixed-use buildings where the elevation is designed around exterior metal wall panels and the design wants the metal read without a cassette system behind it.
  • High-end residential and villa exteriors — entrance zones, feature elevations and balcony walls that need a durable finish with no annual recoating.
  • Industrial and municipal buildings — large wall fields where a factory-finished panel cuts site labour and keeps a consistent surface across several storeys.
  • Schools, hospitals, airports, rail stations and museums — interior walls that take constant use and have to be wiped down without special products.
  • Wet interior areas — bathrooms, kitchens and balconies, where moisture resistance and mould resistance do the work that a gypsum lining cannot.
  • Interior fit-out and joinery — reception and feature walls, ceilings, partitions, doors, cabinetry and display units, using the same face as the exterior for a continuous palette.
  • Marine interiors — cabin linings and partitions on ship fit-out, where a mineral, non-resinous board is preferred.
  • Floors — the board is also supplied for flooring within the build-up the project specifies.

Metal-Look Series & Related Boards

This board sits in the metal-texture band alongside CP-MT-001, CP-MT-003, CP-MT-004, CP-MT-005 and CP-MT-006. All six share the same inorganic substrate, the same grade system and the same three fixing methods; what changes between them is the surface look the face carries and the panel format it is supplied in.

That is the practical difference when you are comparing codes for an elevation. Two metal boards from the band can look quite different side by side — one warmer and more patinated, another cooler or more uniform — so the choice is usually made on the appearance the design team wants and on the format the panel layout needs, not on performance, which stays the same across the band. Ask your sales contact for the finish and the format carried by each reference before you settle the comparison, and check each one against the elevation drawing.

As exterior metal wall panels manufacturers we hold the whole metal-texture band, so a project can be specified from one source rather than split across suppliers. The same substrate family also runs through our stone-look and wood-look series, which means a scheme can keep one material across a facade and its interiors and still change the surface from metal to stone to timber where the design calls for it.

Ordering & Delivery

  1. Send the job details: the application, the wall type, the panel size and thickness, the surface finish, the quantity, the project location and the required delivery date. The more of that you can put in one message, the faster the answer comes back — as an exterior wall panels supplier we quote from the job rather than from a stock list.
  2. We come back with the grade, the colour reference and the packing that suit the order. Minimum order quantity, packing specification and shipping terms are confirmed by your sales contact for your particular project.
  3. Custom orders run on a 30-day production cycle.
  4. Ask your sales contact for the test documentation and the project file pack you need for your submission; we will confirm which documents are available for your market.
  5. For a facade package, send the elevations so exterior metal wall panels can be priced from the panel layout rather than board by board.
  6. Payment terms, port of departure and the shipping schedule are settled with your sales contact when the order is placed.

Surface Care & Replacement

  • Before the panels go up: store them flat, off the ground, under cover and clear of standing water, and keep the decorative face protected until the wet trades and dirty work in that area are finished.
  • Day to day: warm water with a neutral detergent and a soft cloth or mop is enough; rinse and dry the surface afterwards. Abrasive pads, steel wool and solvent-based cleaners dull the face and stay off it.
  • After construction: leave the final wash until the trades that make dust, mortar and paint splashes have finished. Fresh splashes lift off with a cloth far more easily than dried ones.
  • Trimmed edges: a cut panel shows the board core along the edge, so wipe it clean and let it land inside the joint, trim or return the drawing calls for rather than leaving it exposed on a corner.
  • Exterior check: on exterior metal facade panels, look over joint lines, sealant and flashings once a year, on the same visit as the clean. Moisture expansion of the board itself is 0.1% or less; keeping water moving off the wall is what protects the substrate and the fixings behind it.
  • Damage: because panels are fixed individually, a board that is cracked, chipped or deeply marked can be released and replaced on its own without stripping the elevation around it. Check the mark in daylight first — on a matte, speckled face a scuff usually reads far less than it would on a gloss panel.
  • Spare panels: keep one or two panels, or a few large offcuts, from the batch that went onto the wall. A replacement from a later batch may not sit perfectly alongside the panels already fixed, so add the spares to the original order.
  • Avoid: do not drag panels face to face when moving them, do not let sealant, adhesive or paint dry onto the face, and do not use a finished panel as a cutting or mixing surface.

Custom Pattern Matching

  1. Send the reference you want matched — a designer's render, a photograph of a metal already on the building, a pattern drawing or a swatch — and say whether it is a straight repeat, a random speckle or a set pattern. Where the reference has a measured repeat, give that repeat in millimetres.
  2. Say how the pattern should sit on the wall: running continuously across the elevation, or repeating identically on each panel with the joint as the break. Joint positions decide which of the two works, so settle it against the panel layout before anything is made.
  3. We confirm whether the reference sits inside the standard metal-texture range or has to be produced specially for your project, and come back with the colour reference that applies to the order.
  4. A different pattern does not change the material: custom face work stays on the same inorganic board, in the same thickness grades and with the same three fixing methods as the rest of the metal series.
  5. Approve a physical sample close to panel scale, in the light the wall actually receives, before production begins. A pattern that looks right on a small swatch can read very differently once it is repeated across a full panel.
  6. Keep one tone across the elevation by ordering the whole quantity for the job in a single run, and add the spare panels to that run — a pattern produced later may not align tone for tone with the panels already on the wall.
  7. On phased schemes, tell your sales contact at first enquiry which areas are still to come, so the approved pattern and colour reference stay with the project instead of being re-matched from scratch later.

Scale & Supply Capability

CERSAIPANEL is the brand of Yulin Keli Keying Technology Co., Ltd., a building-material manufacturer established in 2016 and based in Yulin, Shaanxi, where we run our own production base with a workforce of 140. Manufacturing and export sit under one roof, so buyers in Europe, North and South America and Australia deal directly with the people who make the goods. Our full range is backed by third-party testing and the international certifications the company holds, and we take on OEM work and custom orders, from first sample through repeat production.

FAQ

Is this a metal sheet, or a board with a metal-look surface?

It is a board. The panel is an inorganic fibre board with a decorative face applied to it at the factory, so the metal appearance is a cured surface on the board rather than a sheet of metal bonded on top of it. It is also not a carbon-fibre-reinforced polymer composite. Because the face comes with the board, there is nothing to laminate or paint on site — the panel is fixed as it is delivered. We are among the exterior metal wall panels manufacturers who supply the board pre-finished, so where a panel has been trimmed the cut edge will show the board core.

How does the board compare with stone or ceramic cladding?

It is offered as the lighter alternative to stone and ceramic cladding, and the difference shows up in two places: the load the wall has to carry, and the way the material is handled on site. A panel arrives flat and pre-finished, so exterior metal wall panels specified in this material are set out and fixed as a panel system rather than laid unit by unit, and there are no mortar or grout joints to repoint later. The apparent density for this board is listed in the specification table above. The finish is applied in the factory, so the elevation keeps the pattern that was approved instead of varying from piece to piece the way a natural material does.

Can the metal-look finish be customised to a design intent?

Yes. Patterns outside the standard metal-texture range can be produced using 3D high-definition printing with electron-beam curing, which is how a project can end up with metal exterior wall panels matched to a specific reference — a designer's render, an existing metal on the building, or a pattern drawn to scale. Send the reference image or drawing with an indication of scale, and check the result against a physical sample of the board before production, because screen colours and small reference swatches both shift when they are printed at full panel size.

What maintenance does the surface need?

Very little. The decorative face is stain, scratch and wear resistant, and routine cleaning with water and a mild detergent is normally enough, indoors and out. Remove aggressive stains promptly rather than letting them sit, and avoid abrasive pads, steel wool and strong solvent cleaners on the face. On exterior metal facade panels it is worth checking the joint lines and flashings at the same time as the annual clean, because keeping water moving off the wall is what protects everything behind the board, whatever the panel is made of.

If one panel is damaged, can it be replaced on its own?

Yes. Panels are fixed individually, so a damaged board can be released and replaced without dismantling the elevation around it. Keep a few offcuts or one spare panel from the same production batch for that purpose, since a later replacement from a different batch may not sit perfectly alongside the panels already on the wall. Scratches that only affect the face are usually less noticeable on this matte, speckled finish than they would be on a gloss surface, so look at the panel in daylight before deciding to change it.

Leave a message
姓名
电子邮件*
信息