CP-ST-001 is a stone-texture board from the CERSAIPANEL range: a rigid, fully inorganic fibre panel with a printed stone face — a pale marble field crossed by grey and charcoal veining. It is made for walls that are specified as panels rather than slab. An exterior elevation, a ground-floor base, an entrance or a lobby wall where a stone look is wanted, in a format that is set out, fixed and replaced board by board.
Panels are flat and rigid, supplied in long formats that cover a facade bay with few joints, and in shorter cuts for returns, soffits and column casings. The thickness that suits a given wall is settled at specification stage, because it follows the substrate, the fixing method and the exposure rather than the surface alone.
Day to day the material behaves like a facade panel: it is set out on a grid, fixed to a prepared background or a subframe, and replaced as an individual board if one is damaged. Nothing about working with it needs a specialist fabricator.
Buyers arrive at this surface from two directions. Some are specifying a stone look for the first time and want to know how it behaves next to real stone. Others already run a facade package and need a material that matches at the base or inside the entrance. The stone, metal and wood surfaces are all made on the same site, so a project that buys facade metal panels direct from manufacturer can add stone-look boards to the same order without opening a second supply line.
| Property | Value |
|---|---|
| Surface | Printed stone look — pale marble field with grey and dark veining |
| Board material | Inorganic fibre board made from coal gasification slag |
| Panel length | Up to 3,050 mm |
| Panel width | Up to 1,220 mm |
| Thickness | 4 mm to 15 mm across the range; exterior walls are normally specified at 10 mm and 12 mm, interior walls at 4, 6, 8 and 10 mm |
| Density | Approximately 950–1,200 kg/m³, or higher depending on the product series |
| Moisture expansion | 0.1% or less, on the supplied test information |
| Screw withdrawal strength | At least 1,870 N, on the supplied test information |
| Fire performance | The supplied test information reports Class A non-combustible material behaviour, and 90 minutes at 1,200 °C for the tested wall-panel system |
| Smoke toxicity | Class t0, on the supplied test information |
| Exterior system performance | Class 5 air tightness, Class 3 water tightness and wind resistance of ±6.0 kPa, on the supplied test information |
| Fixing methods | Wet bonding, riveting, dry hanging |
| On-site fabrication | Can be cut, drilled, nailed and screwed |
The board behind this surface is an inorganic fibre panel made from coal gasification slag — an industrial solid waste that used to be stockpiled and could not be broken down. We melt it twice at 1,500 °C and rebuild the mineral structure, so the finished board is a fully vitreous, glass-phase material rather than a resin-bonded composite. The same core sits behind our metal panels facade and wood-look boards; the series differ by surface, not by material. If you have seen the product name translated as carbon fibre board, that is not what this is: it is not a carbon-fibre-reinforced polymer composite, and it is not natural stone or fired ceramic.
That origin has three consequences a project can use. The board is inorganic, so the supplied test information reports it as formaldehyde-free and benzene-free, with no toxic volatile organic compounds detected — which matters where indoor air quality is part of the brief, such as schools, hospitals and residential interiors. It is dense and rigid rather than soft, so it behaves like a panel on site, holds fixings and takes a knock without the brittleness of a thin tile. And the melting process runs on wind and solar electricity, so production uses green power rather than fossil generation — worth knowing when a project carries an embodied-carbon target.
Where this board is compared with stone slab, ceramic tile and several traditional panel systems, it is the lighter option, which reduces the load the structure has to carry and the handling equipment needed on site. That is a comparison against the materials it replaces, not a claim about a single figure — the load calculation still belongs to your engineer.
What the material does not decide on its own is how it performs on your wall. Fire, weather and moisture results belong to a tested construction — panel specification, substrate, subframe, joints and fixing method together. Send us the wall build-up you are working to, and we will confirm which of the supplied reports applies to it and which documents can be released for the submission.
The three surface families answer three different briefs. Stone-look boards, this series, are chosen where the architecture needs a stone reference: large facade fields, ground-floor bases, entrance zones and lobby walls. Metal-look boards give a cleaner, more uniform surface for contemporary volumes, soffits and service zones, and where the design language is metal our metal facade panels carry the same board with a metal finish. Wood-look boards bring a warm timber reference to interiors, soffits and feature zones, without the moisture and upkeep concerns that come with real timber.
Choosing between them is usually a question about the zone rather than about the whole building. It is common for one elevation to run a metal surface above and a stone-look base at street level, or a stone-look facade outside with a wood-look wall inside the same entrance. Because the surfaces share a board and a fixing logic, the surface can change without changing how the wall is built — but the joint widths, the panel module and the thickness should be agreed across that change, not decided surface by surface.
If you are specifying metal and stone together — buying facade metal panels direct from manufacturer for the upper elevations and stone-look boards for the base — fix the panel module first and let both surfaces follow it. Send us the stone or the reference image you are matching, and tell us which zones take which surface. We will confirm what the line can reproduce and how the two surfaces meet at the transition.
The board itself is inorganic, so there is nothing in it for mould to feed on: no cellulose, no wood flour and no organic binder in the core, and a glass-phase structure that does not soften or swell in damp service. The supplied test information reports moisture expansion of 0.1% or less. If the submission needs the water-absorption figure for this board, ask your sales contact and we will confirm which figure belongs to your specification.
Where mould appears on a wall like this, it usually starts in the construction rather than in the panel — a joint that traps water, a cavity with no drainage, a substrate that stays wet behind a bonded board, or a dirt film holding moisture on the face. Sealing, flashing, drainage and ventilation are what keep a bathroom, kitchen, balcony or laundry wall clean, and the board's part is to stay flat and stable while the rest of the build-up does its work.
Cleaning needs no specialist products. Wipe with a soft cloth or soft brush and a mild neutral cleaner, then rinse or wipe dry. Entrance bases, corridors and washroom walls are touched and washed far more often than an upper elevation, so put them on a routine round instead of waiting for the wall to look tired. Oil, ink and sealant smears come away most readily when they are dealt with promptly, and hard-water marks usually respond to repeating a mild clean rather than to a strong descaler.
What to avoid: abrasive pads, wire wool, gritty creams and strong solvents, all of which dull a printed or polished face faster than they lift the mark. Test any new cleaning product on an offcut before it goes near a finished wall, and use a plastic scraper rather than a metal one on anything stuck to the surface. Sealant joints and flashings are the first things to age on any wall, so check them on the same maintenance round as the panels — most damp problems start at a joint, not at a board face.
Upkeep is where the comparison with real stone and ceramic shows. There is no sealing round, no re-polishing and no efflorescence to wash off, and where a stone wall might be re-faced after damage, here the affected board is replaced on its own. Keep two or three boards from the project batch flat and dry in store: if the surface is disturbed later, a replacement from the same production run blends into the wall around it. On site, keep panels off damp ground and out of standing water, and leave the protective film in place until the wall is finished.
| What to confirm | How to check it | Why it matters |
| Model code | CP-ST-001 on the drawing, the order and the packing list | The code identifies the board and its stone surface together, so the quotation, the approved sample and the delivered panels all refer to the same product. |
| Surface series | Confirm the stone-look series against the approved sample | The range also covers metal-look and wood-look surfaces, and each series carries its own pattern references. List mixed elevations by code rather than by colour name. |
| Colour and pattern | Approve a physical sample and keep it as the project reference | Printed surfaces are checked against the approved sample before packing; a screen image shifts between monitors and again in daylight. |
| Other stone textures | CP-ST-002 to CP-ST-032 are separate stone looks in the same family | If the wall calls for a different stone figure, order that code instead of expecting a colour change on this one. |
| Thickness tier | State the tier on the order | The code does not carry the thickness; the wall, the substrate and the fixing method decide it. |
| Neighbouring surfaces | List the other surfaces on the elevation by code as well | Where facade metal panels run above a stone-look base, ordering the whole elevation as one reference set keeps the module, the joint widths and the surface depths aligned. |
| Later additions | Quote the original model code and, if you have it, the original order or batch reference | A later run is produced to the same specification, and the closest match to an installed wall comes from the same code and, where possible, the same production run. |
CERSAIPANEL is the brand of Yulin Keli Keying Technology Co., Ltd., a building-material manufacturer established in 2016 and based in Yulin, Shaanxi, where we run our own production base with a workforce of 140. Manufacturing and export sit under one roof, so buyers in Europe, North and South America and Australia deal directly with the people who make the goods. Our full range is backed by third-party testing and the international certifications the company holds, and we take on OEM work and custom orders, from first sample through repeat production.
It follows the wall rather than the surface. Exterior work uses the heavier tiers, because the panel has to span between fixings and take wind load on a drained cavity. Interior walls can use the lighter tiers and are often bonded straight onto a flat background. Your substrate, the fixing method and the exposure decide the number, so send us the wall section and we will confirm the thickness that applies before the drawings are frozen.
Production is run against the approved sample, and the printed surface is checked for colour and pattern consistency before packing. Two things make that reliable: approve a physical sample rather than a screen image, and keep it as the reference for the project. If the new boards have to sit beside a wall that is already installed, say so at the enquiry stage so the match can be assessed against an existing panel.
Wipe with a soft cloth or soft brush and a mild neutral cleaner, then rinse or wipe dry. Aggressive stains — oil, ink, sealant smears — should be removed promptly rather than left to sit. Avoid abrasive pads, wire wool and strong solvents, and test any new cleaning product on an offcut before using it across a finished wall.
The boards are individual units, so a damaged panel can usually be cut out and replaced without redoing the surrounding wall. How cleanly it comes away depends on the fixing method: riveted and dry-hung panels release from the subframe, while bonded panels take some of the adhesive with them. Check deliveries before installation begins and report any transit damage with photographs, so it is dealt with before the wall is closed up.
Yes. We are exterior metal wall panels suppliers as well as producers of the stone-look and wood-look boards, and all three series come off the same production base in Shaanxi. A project can therefore take a single surface or the whole elevation from one base, with the same thickness logic and the same fixing advice behind it.
Yes, and it is a common arrangement. Where the metal facade panels and the stone-look boards meet, treat the change as a joint detail: agree the joint width, the panel module and the surface depths on the drawing, and the two materials read as one elevation rather than as two systems. Send the transition detail with your enquiry and we will check it against the fixing method you are using.