Product Overview
These stone facade panels are made rather than quarried. The base is an inorganic fibre board produced from coal gasification slag, and the face carries a deep black stone tone crossed by bold white veins. Because the pattern is printed and cured onto the board, panel one and panel two hundred are produced from the same reference — there is no block-to-block variation to design around.
CP-ST-020 sits in the stone-look band of the range, which runs from CP-ST-001 through CP-ST-032 and stands alongside separate metal-look and wood-look series and a solid aluminium mosaic line. Boards from this band go onto exterior wall cladding and interior wall surfaces, so one look can carry from a ground-floor lobby through to the façade, provided the thickness and the fixing method suit each position.
The people who specify it are usually working to a drawing: architects and façade consultants who want a dark stone appearance without the weight of quarried marble, fit-out contractors who want a panel their own crew can cut and fix, and importers and exterior wall cladding panels suppliers who need one pattern that sells into both exterior and interior projects. On site the board behaves like a rigid panel — it arrives flat, is cut and drilled to the set-out, and is fixed to a prepared substrate. The face leaves the factory finished, so the wall is complete when the fixing is complete.
Surface & Veining Character
- Black ground, bold white veining — The face is a deep black stone tone crossed by white veins that branch and spread as they travel across the sheet. It is the pattern this model carries, and the one most often compared with dark marble.
- Polished, marble-like surface — A glossy finish that deepens the black on shaded elevations and picks up highlights on sunlit ones. Indoors it reads as polished stone; outside, the sheen shifts through the day as the light moves across the wall.
- A printed face made under our own roof — We are the exterior wall panels factory behind the board rather than a trading office reselling someone else's sheet, so the base board is formed and the decorative face is printed and cured on our own 3D high-definition printing line. A repeat order runs on the same process as the original.
- Vein direction is a decision, not an accident — The pattern has a direction. Settle horizontal or vertical before production and mark it on the layout, because turning a board on site changes the way the veins flow across the wall.
- Continuity between panels — Veins do not continue automatically across a joint. Tell us at drawing stage whether you want a continuous run or a deliberately staggered one, and we set the board layout to suit.
- One face for interior and exterior — The same finish is produced for stone facade panels exterior walls and for interior feature zones; what changes between the two is the board thickness and the fixing method, not the look.
- Where the pattern works hardest — Large fields, entrance returns and reception walls give the veining room to be read. On narrow piers and small panels the pattern registers as texture rather than as a vein.
Specifications
| Base material |
Inorganic fibre board made from coal gasification slag |
| Material structure |
Fully vitreous and inorganic — not a carbon-fibre composite |
| Apparent density |
approximately 950–1,200 kg/m³, depending on the series |
| Moisture expansion |
0.1 % or less |
| Mould resistance |
Tested mould resistant |
| Screw withdrawal strength |
at least 1,870 N |
| Interior wall thickness options |
4 mm / 6 mm / 8 mm / 10 mm |
| Exterior wall thickness options |
10 mm / 12 mm |
| Thickness range across the series |
4–15 mm, depending on the product series |
| Panel length |
up to 3,050 mm |
| Panel width |
up to 1,220 mm |
| Decorative process |
3D high-definition printing, electron-beam cured |
Installation & Fixing Methods
- Prepare the substrate — The wall needs to be flat, dry and sound, with no loose material, before panels arrive. Flatness tolerance and any priming requirement follow the fixing method, so settle the method before the substrate is signed off.
- Choose the fixing method — Wet bonding, riveting and dry hanging are all used with this board. For stone facade panels for exterior use, riveting or dry hanging is normally specified so that each panel stays independently fixed to its frame; interior walls are more often wet bonded onto a prepared substrate. Confirm the method against your own detail drawing.
- Set out the panel grid — Mark the layout on the wall from the drawing, including joint positions, vein direction and the position of any panel that has to be cut. Working to a marked grid is what keeps the joints straight over a long elevation.
- Cut and drill on site — The board can be cut, drilled, nailed and screwed with ordinary woodworking tooling. Support both sides of the sheet while cutting, extract the dust, and take the cut edge back with a fine abrasive so the joint closes cleanly.
- Fix and align as you go — Work from a fixed datum rather than from the previously fixed panel, check the joint line with a straight edge every few panels, and wipe adhesive or sealant off the face while it is still fresh.
- Clean down and inspect — Once the wall is complete, remove dust and residue from the face and check the joints and corner details, confirming any drainage and ventilation path behind the cladding where the system has one, before the scaffold comes down.
Material & Build
Every CERSAIPANEL board starts with coal gasification slag — an industrial solid waste that used to sit in piles and could not be broken down. We melt it twice at 1,500 °C and restructure it, burning out the harmful components and leaving clean mineral chemistry behind. What comes out is a fully vitreous, inorganic board rather than a resin-bonded sheet or a conventional carbon-fibre composite, and the supplied testing reports it as formaldehyde-free and benzene-free, with no toxic volatile organic compounds detected.
The base material is documented as Class A non-combustible, and the tested wall-panel system is reported at 90 minutes of fire resistance at 1,200 °C, with smoke toxicity classified as t0. Those figures belong to a defined construction — a particular thickness on a particular substructure, with a particular joint and fixing pattern — so when a project needs the number in writing, match the report to your own build-up rather than quoting the headline figure. Surface performance matters just as much day to day: the face takes a screw fixing and resists staining, scratching and ordinary wear once the wall is up.
Weight is where the material changes the economics. A quarried or cast alternative of the same coverage puts considerably more load on the substrate, the frame and the lifting equipment, and that load has to be designed in from the start. With this board, panel size and panel thickness come from your drawing instead of from whichever block happens to be available, so a stone facade panels exterior elevation can be planned the way a metal façade is planned.
The decorative face is applied on our own printing line, which is the practical reason exterior wall cladding panels suppliers can hold a stone pattern as a stock line: the same reference is reproduced on the next order, in the thickness and panel size that order needs, without a second supplier in the chain.
Applications
- Building façades — Long, uninterrupted elevations are where these stone facade panels for exterior walls do their main work. One pattern carries from ground to parapet, where quarried stone would change character slab by slab, and the boards go up over a prepared substrate rather than being bedded like tile.
- Entrance zones and ground-floor returns — Positions seen at hand distance. A polished black face with white veining gives an entrance weight without the thickness of a stone-clad wall, and the set-out can be aligned to door reveals and column lines.
- Interior feature walls and reception areas — The same stone facade panels work indoors: office lobbies, hotel receptions, commercial walls and lift surrounds, where the board can run full height with fewer joints than a tiled finish.
- Wet interior areas — Bathrooms, kitchens and balcony walls, where a dark stone look is wanted on a surface that does not need the protection a natural stone or timber wall would.
- Institutional interiors — Schools, hospitals, airports, rail stations and museums, where corridor walls have to survive trolleys, cleaning and heavy foot traffic without losing the finish.
- Distributor and stock ranges — A single pattern that answers both façade enquiries and interior fit-out enquiries keeps one stock line working across two product types, which is why importers often start with this finish.
Ordering & Delivery
- Send the wall position and the drawing — An elevation, layout sketch or panel schedule is enough to start. Include the panel length and width you need, where the board is going (exterior wall, interior wall, wet area or soffit) and the vein direction.
- Confirm the thickness grades for your position — The grades this stone-look board is produced in depend on where it is going, and the choice changes the fixing method and the substrate. Tell us the position and we confirm the options before you price the job.
- Order from the factory — We are the exterior wall panels factory behind the board, so the base and the printed face are made under one roof and a repeat order is matched against the earlier production rather than re-sourced.
- Confirm quantity, packing and commercial terms — Order minimums, packing method and delivery arrangements depend on the total quantity, the panel size and the destination, so they are confirmed with the quotation rather than assumed. If the board has to match a colour reference, send it with the enquiry.
- Allow 30 days for a custom order — Custom orders are produced on a 30-day cycle from confirmation of the drawing, finish and quantity. Ask your sales contact to check that schedule against your installation programme before the fixing date is committed.
- Approve the finish on a physical piece — Before the order is released, check the pattern and the colour reference on a real piece rather than on a screen; ask your sales contact about sample availability and which reference applies to this pattern.
- Plan the repeat order — Importers and exterior wall cladding panels suppliers usually begin with one pattern and one thickness and extend the range once the first wall is up. Tell us which pattern and thickness you intend to hold and we set the repeat production up around it.
Maintenance & Panel Repair
- Upkeep is cleaning labour, not resurfacing — Because the black face is printed and cured rather than polished out of a block, there is no honing, sealing or re-polishing to schedule over the life of the wall. Budget the post-handover cost as a routine wipe-down plus a periodic check of the joint line.
- Working down a large elevation — A polished face shows runs if dirty water is left to dry on it, so wash in sections from the top down, rinse with clean water as you go, and finish with a dry pass instead of letting the elevation air-dry.
- Exterior elevations set their own rhythm — Rain sheds light dust from stone facade panels on exterior walls, so clean when the elevation starts to read dull or streaked rather than to a fixed calendar; a road-facing or tree-shaded wall needs attention more often than a sheltered one.
- Joints and seals are the part that ages — The board has no maintenance item of its own, so put the periodic inspection into the sealant line, the corner trims and the drainage and ventilation path behind the cladding, and renew whatever has failed.
- Store boards flat and dry — Keep panels level, off the ground and clear of standing water, with the face protected, and lift rather than drag them; grit trapped between two boards scratches a polished face before it is ever fixed.
- Order the spares with the wall — A replacement board matches closest when it comes from the same production run, so add spares to the main order, store them flat alongside the setting-out drawing, and label them with the pattern reference, panel size and thickness.
- Replacing one board in a finished wall — The damaged panel is cut free of its sealant and released from the frame, the new board goes on against panels that are already fixed, and the joint and the water path behind the cladding are reinstated as part of the repair rather than left until later.
- What to send us for a replacement — A photo of the damage, the pattern reference and batch recorded on the drawing, the panel size and thickness, and the fixing method used; we check what is still running against that batch and confirm how close the match will be.
- Check deliveries before the boards go up — Inspect panels on arrival, note any transit or handling damage on the delivery paperwork, and set damaged boards aside rather than fixing them into a finished elevation.
Scale & Supply Capability
CERSAIPANEL is the brand of Yulin Keli Keying Technology Co., Ltd., a building-material manufacturer established in 2016 and based in Yulin, Shaanxi, where we run our own production base with a workforce of 140. Manufacturing and export sit under one roof, so buyers in Europe, North and South America and Australia deal directly with the people who make the goods. Our full range is backed by third-party testing and the international certifications the company holds, and we take on OEM work and custom orders, from first sample through repeat production.
FAQ
What happens if a panel is damaged?
Keep two or three spare panels from the same production batch on site, and note the fixing method used on the as-built drawing. Because the face is printed, replacing one board is a local job rather than a whole-elevation one: the damaged panel is released, a new board is set in and the joint is re-sealed. On any stone facade panels exterior installation the replacement also closes the point where water could get in behind the cladding, so it is worth doing as soon as the damage is spotted rather than at the end of the programme.
Will the white veining line up from one panel to the next?
Only if the layout is planned that way. The pattern is printed board by board, so the veins do not continue automatically across a joint — where an elevation of stone facade panels for exterior use is seen at once, that is the detail to settle before production rather than on the scaffold. Send the elevation with the panel grid marked and say whether you want a continuous run or a staggered one, and we set the boards to suit.
How are corners, returns and window reveals detailed?
Corners are set out at production stage rather than improvised on site. A return or a reveal normally takes a cut panel with the joint placed on the corner line, and an aluminium or stainless trim section is the usual way to close an external corner if you would rather not have the board edge on show. Send the corner detail with the layout drawing — the joint position and the trim section are confirmed against it, and the set-out is adjusted so the trim lands on a full panel where the geometry allows.
How do I clean the polished face without dulling it?
Dust the wall with a soft dry cloth or a microfibre mop first, then wipe with a damp cloth and a mild neutral detergent. Rinse with clean water and dry the surface so no film is left behind. Abrasive pads, scouring powder and strong solvents are what dull a polished face, so keep them away from it, and deal with oil, ink or sealant marks as soon as they appear rather than letting them sit. No wax or polish is needed afterwards.
How tight are the joints, and how visible will they be?
Joint width comes from the fixing system and the substrate, not from the board alone. Closed joints give a wall that reads as an almost continuous stone surface and are the usual choice for interior feature walls. Open joints with a shadow gap are common where the cladding has to move with temperature and where ventilation and drainage sit behind the panels. The decision changes the panel sizes and the board count, so make it at drawing stage and confirm the joint width against the system you are using.
Can the same board be used on a ceiling or a soffit?
Yes — ceilings and soffits are normal positions for the board, and what changes is the fixing rather than the panel. Overhead work is mechanically fixed to a frame instead of bonded, because gravity is working against the adhesive, so the frame and the set-out are designed together. Tell us the position when you send the layout and we will confirm the fixing arrangement for it.